In uneven road surfaces such as mine gravel roads, construction site mud areas, and agricultural fields, the high ground clearance forklift , with its ultra-large distance between the chassis and the ground, has become a core equipment to avoid collisions and ensure smooth passage. Compared with ordinary forklifts with a ground clearance of 15-20cm, the high ground clearance forklift usually reaches more than 30cm, which can easily cross obstacles such as stones and gullies, completely solving the "chassis jamming" pain point in outdoor operations. This article analyzes the core advantages, selection standards, and application scenarios of the high ground clearance forklift to help you match suitable equipment.

1. Why is the High Ground Clearance Forklift a Necessity for Outdoor Operations?

The core value of the high ground clearance forklift lies in the dual guarantee of "anti-collision + strong passability": its elevated chassis design can reduce the risk of collision with ground obstacles by more than 90%. In ore areas full of gravel, the high ground clearance forklift can avoid rocks scratching the fuel tank or drive shaft; in rainy and muddy construction sites, sufficient ground clearance can prevent power loss caused by mud wrapping the chassis. Data shows that in outdoor projects equipped with high ground clearance forklifts, equipment failure rates are reduced by 60%, and downtime for maintenance is shortened by 50%—this is the key reason why the high ground clearance forklift is widely favored.

2. Key Performance Indicators of the High Ground Clearance Forklift

Ground Clearance Parameters: A high-quality high ground clearance forklift must have a minimum ground clearance of ≥300mm, and both approach and departure angles of ≥25° to ensure that the front fork does not scrape against the ground when going up and down slopes.

Chassis Structure: Using a reinforced frame and extended suspension, the chassis components of the high ground clearance forklift need to be equipped with protective plates to avoid hitting the gearbox or hydraulic pipelines.

Power Configuration: Equipped with a high-power engine (such as 103kw class) and a low-speed, high-torque gearbox to ensure that the high ground clearance forklift still has sufficient power and does not slip when climbing despite the elevated center of gravity.

Stability Design: Widened wheelbase and heavy-duty axles (such as GS30 type) can balance the upward shift of the center of gravity caused by the high chassis, which is the basis for the safe operation of the high ground clearance forklift .

3. Selection Strategies for High Ground Clearance Forklifts in Different Scenarios

Mine Material Transfer: Prioritize high ground clearance forklifts with a ground clearance of more than 350mm, combined with puncture-resistant tires to cope with frequent impacts from sharp ores and ensure continuous operation of the equipment.

Agricultural Field Operations: Recommend models with a ground clearance of 300-350mm. The high ground clearance forklift needs to avoid slow steering caused by excessive elevation, balancing passability and operational flexibility.

Construction Site Off-Road: Choose a high ground clearance forklift with adjustable ground clearance function, switching between "high clearance passage mode" and "low clearance stability mode" according to road flatness to improve scenario adaptability.

3. Maintenance and Care Points for High Ground Clearance Forklifts

Chassis Inspection: Clean the mud and gravel attached to the chassis after daily operations, and tighten suspension bolts weekly to prevent loose components of the high ground clearance forklift due to vibration.

Tire Maintenance: Regularly adjust tire pressure (adapt to 0.8-1.0MPa according to load) to ensure the support stability of the high ground clearance forklift on uneven roads and reduce component wear caused by bumps.

Steering System Maintenance: Check the wear of steering tie rods and ball joints every 200 hours of operation. The steering accuracy of the high ground clearance forklift directly affects the operational safety in complex terrains.

Hengwang Group Off-Road Forklift : A Reliable Representative of High Ground Clearance

Hengwang Group's off-road forklift series is specially designed for complex terrains, and its high ground clearance feature perfectly adapts to outdoor operation needs. Taking the HWC-60A as an example, the equipment achieves an ultra-300mm ground clearance through optimized chassis structure. Combined with 12R22.5 vacuum steel wire tires, the high ground clearance forklift can easily pass through muddy and gravel roads, avoiding chassis collisions. Equipped with a 103kw Xichai engine and a heavy-duty axle, the high ground clearance forklift, while ensuring passability, also has a 6T load capacity and a 4-meter lifting height to meet heavy-load handling needs. The user-friendly operating handle and hydraulic dumping device further improve the operational efficiency of the high ground clearance forklift. Relying on the "four-dimensional integration" service system, Hengwang provides 24-hour after-sales support to ensure continuous and stable operation of the equipment.

Take Action Now: Leave your operation terrain and obstacle height to obtain a customized high ground clearance forklift selection plan. The Hengwang technical team will respond within 24 hours! Choosing Hengwang high ground clearance forklift can turn the passage in complex terrains from "full of obstacles" to "smooth and unimpeded", escorting outdoor operations.